Check fuel lines for signs of wear, deterioration, damage or leakage. Replace if necessary. Be sure fuel lines are routed properly and secured with cable ties. Replace all fuel lines every two years. Check fuel tank, oil tank, carburetor, battery and transmission vent lines for signs of wear, deterioration, damage or leakage. Replace every two years. Be sure vent lines are routed properly and secured with cable ties. The fuel filter should be replaced in accordance with the Periodic Maintenance Chart.
The fuel filter is located between the fuel pump and carburetor. Shut off fuel supply at fuel valve. Remove line clamps at both ends of the filter. Remove fuel lines from filter. Install new filter and clamps onto fuel lines with arrow pointed in direction of fuel flow. Install clamps on fuel line. Turn fuel valve ON. Start engine and inspect for leaks, refer to Harley manual for more information.
The carburetor float bowl should be drained periodically to remove moisture or sediment from the bowl, or before extended periods of storage. Turn fuel valve to the off position. Place a clean container beneath the bowl drain spigot or bowl drain hose. Turn drain screw out two turns and allow fuel in the float bowl and fuel line to drain completely.
Inspect the drained fuel for water or sediment. Tighten drain screw. Start machine and check for leaks. NOTE : If there is a tube attached, it must be reattached as this will effect engine performance. Inspect shift linkage tie rod ends, clevis and pivot bushings and replace if worn or damaged.
Place gear selector in neutral. Loosen rod end adjuster jam nuts on both ends of linkage rod. Turn linkage rod to shorten or lengthen rod until the shift lever is centered on hole in the fender. Hold rod end parallel to mounting surface and tighten jam nuts securely.
Check for smooth throttle opening and closing in all handlebar positions. Throttle lever operation should be smooth and lever must return freely without binding. Place the gear selector in neutral. Set parking brake. Start the engine and let it idle. Turn handlebars from full right to full left. If idle speed increases at any point in the turning range, inspect throttle cable routing and condition.
If cable is routed properly and in good condition, repeat adjustment procedure. Replace the throttle cable if worn, kinked, or damaged. If the choke knob does not stay out when pulled, adjust the choke tension by tightening the tensioner located under the rubber boot between the choke knob and nut.
Firmly grasp the rubber boot and tighten until the choke slides freely but stays out when pulled. Verify free play of see reference manual links and smooth operation of choke cable. If smooth choke operation is not obtainable, inspect choke cable for kinks or sharp bends in routing. The pilot systemsupplies fuel during engine operation with the throttle valve closed or slightly opened. Start engine and warm it up to operating temperature about 10 minutes.
Turn pilot screw in clockwise until lightly seated. Turn screw out the specified number of turns. Set idle speed to RPM. Always check throttle cable freeplay after adjusting idle speed and adjust if necessary. Slowly turn mixture screw clockwise using the pilot screw wrench until engine begins to miss.
Slowly turn mixture screw counterclockwise until idle speed increases to maximum RPM. Continue turning counterclockwise until idle RPM begins to drop. Center the pilot screw between the points in Step 5 and 6. Re adjust idle speed if not within specification. Start engine and warm it up thoroughly. Adjust idle speed by turning the idle adjustment screw in clockwise to increase or out counterclockwise to decrease RPM. NOTE : Adjusting the idle speed affects throttle cable freeplay and electronic throttle control adjustment.
To remove the ETC cover: 1. Use a medium flat blade screwdriver and insert blade into the pockets of the cover starting on the 1 position.
Twist screwdriver slightly while lifting on the cover to release snap. Repeat procedure at the other five locations as shown. NOTE : Do not attempt to remove cover until all latch points are released. Remove spark plug high tension lead. Clean plug area so no dirt and debris can fall into engine when plug is removed.
Remove spark plug. Inspect electrodes for wear and carbon buildup. Look for a sharp outer edge with no rounding or erosion of the electrodes. Clean with electrical contact cleaner or a glass bead spark plug cleaner only. Measure gap with a wire gauge. Refer to specifications for proper spark plug type and gap.
Adjust gap if necessary by bending the side 0electrode carefully. If necessary, replace spark plug with proper type. Apply a small amount of anti-seize compound to the spark plug threads.
Install spark plug and torque to ft. Refer to Electrical chapter for ignition timing procedure. Just after realizing the significance of Honda Cr Service Manual Free Download , certainly you can identify why this kind of type of book is genuinely desired.
By figuring out the information, the probability is you might give the top treatment method towards the auto. As outcomes, there is not going to be important challenge or even breakage because you have misused the auto. The offline edition, or genuine book, is often included to the bundle for each acquire.
This can be a superb alternative in case you are certainly not definitely into technologies, or in the event you tend not to choose to have exhausted eyes for viewing pc or smartphone to study the book. The place to obtain this valuable file? You only need to input details about your vehicle 12 months and form and click Go. The web site will method and display you the outcome. In addition to, the manual may also be obtained via third-party web sites.
Also, some internet websites demand you to register, therefore it is considered as impractical. For reliable third party web-site, you could pick eBay or Amazon.
Nonetheless, when you discover Honda Cr Service Manual Free Download from third party website, in particular unreliable one, the material might be various. Honda Owners Manual.
0コメント